
Luxury Corten steel lighting
Corten steel lights and lanterns
Corten steel lights: flame lanterns Aurore, Flora, Stella and Vesper, the Luminus LED bollard, façade and indoor wall lights, a floor lamp and pendants.
Corten garden lights, from the terrace path to the entrance hall
Flame on the terrace, LED on the path
When the terrace comes to life after dark, the simplest light of all is a flame. Aurore, Flora, Stella and Vesper, our four Corten lanterns, take a candle or a decorative fire and need no wiring, and their laser-cut crowns break the glow into patterns, rounded on Aurore and Flora, straight-lined on Stella and Vesper. Stella and Flora, lanterns 450 mm high, keep company with an outdoor lounge, while the two columns, Aurore and Vesper, stand a metre tall to announce the start of a path. Where a switch is preferred, Luminus, a Corten bollard light, guides the way with a warm LED aimed at the ground, from a 2 mm post standing 450 to 750 mm.
On the façade and at the door
With Corten wall lights, a façade can be drawn in light in three ways. Set in pairs on either side of the door, or repeated along the wall, Solan casts two blades of light onto the render from a slender bar of 600 to 1200 mm. Nérite glows like an ember beside an entrance, its light escaping through the oblique slit between two folded panels, and Angle Dièdre folds over the corner of the building like a chevron. The electrical connection and the fixings are a job for a qualified electrician, since Cortenys supplies its lights ready to install but does not fit them on site.
Inside, under a clear varnish
Five Corten lights carry the patina indoors, sealed in our workshop under the protective varnish, compulsory for any of our pieces used inside the home, which strongly reduces transfer to floors and walls without ruling it out; we recommend felt pads or a tray under the Sirius floor lamp, avoiding a very light or porous wall for the wall lights, and protecting the floor below the wall and pendant lights. In an entrance hall or along a corridor, Eos draws a single upright line of light and Aura frames a square glow, 300 to 500 mm a side. In a living room, Sirius rises 1200 to 1800 mm with a line of light along its full height, and above a long table or a kitchen island hang Lyra and Astra, our two pendants.
FAQ
What gives Vesper its pattern of light?
Its crown. Laser-cut in straight lines, in the manner of a steel mashrabiya, it holds the flame high and breaks its glow into a crisp, graphic pattern around the column. Aurore, the other tall lantern, has a rounded foliage motif instead. Both are lit with a candle or a decorative fire, outdoors only.
Which outdoor lights can have the protective varnish?
Luminus and the three wall lights, Solan, Nérite and Angle Dièdre, offer it as an option in the configurator. Formulated for outdoor use, in full sun as in rain, it fixes the patina in its workshop state and greatly reduces marks on pale stone or render without ruling them out, so we still recommend protecting light paving beneath them. The four flame lanterns come in their signature patina only.
What do the lanterns bring by day?
Unlit, they read as sculptures. A column such as Vesper or Aurore gives structure to a planted bed or a path, while the cubes of Stella and Flora add a crisp, graphic note to the terrace. Their patina changes with the light through the day, and at nightfall the flame takes over.
Corten steel lights and lanterns / The models
Our selection of Corten steel lights and lanterns
We shape each creation by hand, with the care that your space deserves.
Cortenys
Caring for your Corten steel lights and lanterns

01 / Advice
Light up the right place
The cutting of the metal and the position of the light source give the Corten luminaire its expression. When turned off, the light reveals its texture; lit, it creates a warm atmosphere. Indoor or outdoor use is verified for each model. Identify circulation areas, walls and connection points. Check each sheet for equipment, installation and authorized indoor or outdoor use. No stock of finished creations: each creation is shaped by hand after its owner's order.



02 / Advice
A creation tailored to the space
We look at your space, the setback and the access points to find the right proportions. We invite you to compare dimensions and weight on the product pages. Individuals, architects or landscapers, entrust us with the desired atmosphere and the measurements of your project to study an adaptation.

03 / Advice
Certified Corten from Italy, three weeks of hand patina
We choose authentic, certified Corten steel from Italy, far from steel with a neglected patina. We shape each creation by hand, without exception. Three weeks of hand-worked patina reveal its nuances; we stabilize it as much as possible. We find a drawing, never quite the same light.

04 / Advice
The varnish option, to support your use
Depending on the creation or your request, we provide a protective varnish to limit dripping in contact with water and patina deposits. We require this varnish for interior models. We advise you according to the exposure and the support, recommending to protect light or porous surfaces. Even varnished, Corten can leave marks.

05 / Advice
Delivery of 5 to 12 weeks
We start after your order. We do not stock any finished creations: prolonged storage in closed packaging harms their patina. We deliver 5 to 12 weeks after confirmation, combining shaping, patina, rest, checks, hand packaging and transport. We invite you to prepare suitable access and handling means.

06 / Advice
The demands of the House, even in the service
We look at Corten like a new gold: its depth, its light and the time of our hands make its value. We are a House, not a factory. We may refuse a request to avoid overproduction and maintain care for each creation. We support you in the choice, the preparation of its arrival and after its delivery, with the same attention.

07 / Cortenys
The corner of the wall, traced in light
Dièdre folds its two Corten steel wings over the edge of the building and spreads a warm glow on either side.

08 / Cortenys
Bars of light on the façade
Solan raises a vertical bar of Corten steel that lights the wall from both its sides, in three heights from 60 to 120 cm.
09 / Cortenys
Light that guides each step
A bollard light in 2 mm Corten steel, Luminus casts a warm LED glow low along the borders and paths.
10 / Cortenys
Lanterns where the flame dances
Vesper rises as a tall openwork column, Stella sits at table height: the cutwork of the Corten steel turns the flame into a lace of light.

Corten steel lights and lanterns / Perspectives
In their setting.
Made to order
The time each piece deserves.
We shape each creation by hand, without exception, after your order. No stock: storage in closed packaging harms the patina. We devote 5 to 12 weeks to artisanal work and care.
5 to 12 weeks
Preparation
Included in the total lead time
We check configuration, dimensions and delivery. For Corten, we choose an authentic material certified from Italy.
Making
Included in the total lead time
We shape each creation by hand, without exception. We take care of the folds, welds and adjustments to give the design its clean lines and precise assemblies.
Cortenys signature patina
three weeks
We work the Corten patina by hand over three weeks. Between each stage and period of rest, we return to its shades, then stabilise it as far as possible. Depending on the piece or your request, we provide a protective varnish to limit runoff when the metal meets water. We require varnish indoors and recommend protecting pale or porous surfaces.
Delivery
Included in the total lead time
We check and then package each creation by hand. We adapt its protections to transport to preserve angles and surfaces, avoiding trapping humidity against the patina.
We develop the Corten patina by hand over three weeks, within the overall delivery window of 5 to 12 weeks. We allow the material to rest, inspect it and prepare it carefully for its journey.
Cortenys
Corten steel lights and lanterns: frequently asked questions
What formats are available?
We present dimensions and options on each product sheet. We study any bespoke format before committing.
Can Corten stain the floor?
We stabilize the patina as much as possible. Depending on the creation or your request, we offer a varnish to limit drips in contact with water, without excluding them. We recommend protecting light or porous floors with spacers, gravel or a saucer.
How to prepare for delivery?
We deliver 5 to 12 weeks after confirmation. We invite you to check access and handling, then unpack and check the creation upon receipt. In case of damage, send us photos of the creation and packaging with your order reference.
Which finish to choose for Corten?
We develop the Corten patina by hand over three weeks. Depending on the creation or your request, a protective varnish limits drips without excluding them. We require this varnish for indoor use and recommend protection of sensitive surfaces.
A particular project in mind?
We study your space, its dimensions and its finish. We select projects to which we can give our full attention.
Cortenys collections












