
Tables, chairs and armchairs for the home
Corten steel tables and seating
Corten steel tables and seating: Orphée, Dorian, Silas, Eurydice and Hestia.
A Corten table, chair and armchair for the home
Around a table of stone
In the dining room, Orphée is the piece everything else gathers around. Its marble top, black for a darker room or white for a bright one, rests on two wide loops of Corten steel that hold the stone like a pair of open hands, in lengths from 2000 to 2800 mm, at a constant height of 750 mm. Pulled up to it, Eurydice is a cantilevered Corten chair with no rear legs: in white upholstery it brightens the stone, while in black it gives the room a darker, sharper outline.
Coffee tables and armchairs for the reception room
In the reception room, the Corten coffee table sets the register. Dorian, with something of the Doric order in its rigour, places a fine-edged slab of black marble veined with white on a square Corten case, 800 to 1200 mm a side, and belongs between two armchairs or at the centre of a large room. Silas reads at a glance, like a roof frame: two timber beams carried by open Corten frames, 1400 to 1800 mm long, with the floor left visible beneath; like Dorian, it is 350 mm high. Hestia, the Corten armchair named after the goddess of the hearth, sets an ecru bouclé cushion on a low Corten base, 760 to 920 mm wide, and can be repeated along a reception room as easily as placed alone.
Sealed before it leaves the workshop
Every Corten part of these five pieces is sealed in our workshop: once the Cortenys signature patina has matured, the protective varnish fixes it in that state, deepens its tones slightly and strongly reduces rust transfer to floors, rugs or upholstery, without ruling it out: we recommend felt pads under the feet and no direct contact with light or porous floors. Marble and timber keep the finish proper to each material. Day to day, a damp sponge is all the steel needs, and its colour stays as it was chosen.
FAQ
Can Orphée or Hestia be used outdoors?
No: like the other pieces in this collection, they are designed for interiors, pairing varnished Corten steel with marble, timber and bouclé, materials chosen for life indoors. Even varnished, the steel can still mark a pale floor, so we recommend felt pads under the feet. For a terrace, look instead at our outdoor Corten pieces, where planters, fire tables and lanterns carry the same patina into the open air.
Which lights suit the Orphée table?
Lyra, a linear Corten pendant from 1200 to 1800 mm long, follows the length of a dining table, and the Orphée product page describes the table set beneath it. The faceted Astra, hung alone or in a cluster, directs its light down towards the table. Both are interior pieces, varnished in our workshop like the table itself; even varnished, the table's Corten base can still mark a pale floor, so we recommend felt pads beneath its feet.
How heavy are these pieces?
Each product page gives an indicative weight: around 225 to 350 kg for Orphée, depending on its length, 75 to 150 kg for Dorian and 115 to 170 kg for Silas, with their stone or timber tops, 42 to 55 kg for Hestia, and about 15 or 16 kg for a Eurydice chair, light enough to draw up to the table.
Corten steel tables and seating / The models
Our selection of Corten steel tables and seating
We shape each creation by hand, with the care that your space deserves.

Tables, chairs and armchairs for the home
The spirit of the collection
Explore the collection, dimensions and finishes.
Corten steel garden ideas: 9 ways to shape a garden or terraceCortenys
Caring for your Corten steel tables and seating

01 / Advice
Match table and seats
In Corten tables and seats, the House takes care of the proportions and the meeting of materials. Check the heights, passages and intended use on the product pages. For interiors, the varnish limits runs and deposits without excluding stains; protect sensitive media. The Maison shapes your creation by hand, after your order, with the options offered by the model.



02 / Advice
A creation tailored to the space
We look at your space, the setback and the access points to find the right proportions. We invite you to compare dimensions and weight on the product pages. Individuals, architects or landscapers, entrust us with the desired atmosphere and the measurements of your project to study an adaptation.

03 / Advice
Certified Corten from Italy, three weeks of hand patina
We choose authentic, certified Corten steel from Italy, far from steel with a neglected patina. We shape each creation by hand, without exception. Three weeks of hand-worked patina reveal its nuances; we stabilize it as much as possible. We find a drawing, never quite the same light.

04 / Advice
The varnish option, to support your use
Depending on the creation or your request, we provide a protective varnish to limit dripping in contact with water and patina deposits. We require this varnish for interior models. We advise you according to the exposure and the support, recommending to protect light or porous surfaces. Even varnished, Corten can leave marks.

05 / Advice
Delivery of 5 to 12 weeks
We start after your order. We do not stock any finished creations: prolonged storage in closed packaging harms their patina. We deliver 5 to 12 weeks after confirmation, combining shaping, patina, rest, checks, hand packaging and transport. We invite you to prepare suitable access and handling means.

06 / Advice
The demands of the House, even in the service
We look at Corten like a new gold: its depth, its light and the time of our hands make its value. We are a House, not a factory. We may refuse a request to avoid overproduction and maintain care for each creation. We support you in the choice, the preparation of its arrival and after its delivery, with the same attention.

07 / Cortenys
A dining room in Corten steel and marble
Orphée carries a marble top on two loops of Corten steel, surrounded by Eurydice chairs. Indoor pieces, delivered with our protective varnish; even varnished, Corten can still mark a light floor, so we recommend felt pads under the feet.

08 / Cortenys
Two coffee tables, two noble materials
Dorian crowns a Corten steel plinth with veined black marble; Silas sets two beams of solid wood on patinated frames.

09 / Cortenys
The softness of bouclé, the anchor of Corten
Hestia wraps a seat in ecru bouclé and sets it on a Corten steel base patinated in the workshop. Three sizes, made to order.

Corten steel tables and seating / Perspectives
In their setting.
Made to order
The time each piece deserves.
We shape each creation by hand, without exception, after your order. No stock: storage in closed packaging harms the patina. We devote 5 to 12 weeks to artisanal work and care.
5 to 12 weeks
Preparation
Included in the total lead time
We check configuration, dimensions and delivery. For Corten, we choose an authentic material certified from Italy.
Making
Included in the total lead time
We shape each creation by hand, without exception. We take care of the folds, welds and adjustments to give the design its clean lines and precise assemblies.
Cortenys signature patina
three weeks
We work the Corten patina by hand over three weeks. Between each stage and period of rest, we return to its shades, then stabilise it as far as possible. Depending on the piece or your request, we provide a protective varnish to limit runoff when the metal meets water. We require varnish indoors and recommend protecting pale or porous surfaces.
Delivery
Included in the total lead time
We check and then package each creation by hand. We adapt its protections to transport to preserve angles and surfaces, avoiding trapping humidity against the patina.
We develop the Corten patina by hand over three weeks, within the overall delivery window of 5 to 12 weeks. We allow the material to rest, inspect it and prepare it carefully for its journey.
Cortenys
Corten steel tables and seating: frequently asked questions
Can Corten steel furniture be used indoors?
Yes, on one condition: varnish. At Cortenys, every piece intended for indoor use receives the mandatory protective varnish, over the signature patina applied in the workshop.
What formats are available?
We present dimensions and options on each product sheet. We study any bespoke format before committing.
Can Corten stain the floor?
We stabilize the patina as much as possible. Depending on the creation or your request, we offer a varnish to limit drips in contact with water, without excluding them. We recommend protecting light or porous floors with spacers, gravel or a saucer.
How to prepare for delivery?
We deliver 5 to 12 weeks after confirmation. We invite you to check access and handling, then unpack and check the creation upon receipt. In case of damage, send us photos of the creation and packaging with your order reference.
Which finish to choose for Corten?
We develop the Corten patina by hand over three weeks. Depending on the creation or your request, a protective varnish limits drips without excluding them. We require this varnish for indoor use and recommend protection of sensitive surfaces.
A particular project in mind?
We study your space, its dimensions and its finish. We select projects to which we can give our full attention.
Cortenys collections




